Valby SG41HD Stone & Waste Grapple

Valby SG41HD Stone & Waste Grapple

This Valby (Intermercato) Grapple has a Two Prong Jaw on One Side, & a Single Jaw on the Other. The Jaws & the Wear Parts are Made Out of Hardox Steel.

Besides Lifting Stones, this Grapple Can Also be Used for the Handling of Logs. The Form of the Jaws is Such that the Grab Also Penetrates Into Piles of Brush or Logging Slash.

The Grapple Opens to 41". To Hold Anything Securely in the Grapple, It Must Close at Least 10". Besides Stones, One Can Handle Logs, Brush & Logging Residue with These Grapples.

Valby SG41HD Stone and Waste Grapples

Intermercato SG41HD Stone and Waste Grapples

Valby SG-41HD Stone Grapples
The SG41HD Penetrates Easily in Piles of Brush & Can be Used for Feeding Wood Chippers & Tub Grinders.

  • Quality Grapples Have Jaws that are Made of Weldox 700 Steel, & Have Wear Plates.
  • Every Joint in a Valby Grapple has a Grease Fitting & a Bronze Bushing.
  • The Valby Grapples Have Powerful Cylinders with Heavy Pistons.
  • Twin Connection Rods Provide Good Balance & Less Stress.
  • A Belly Plate Protects the Cylinder from Below.
  • The Valby Grapples are of Modern Bypass Grapple Design that Support the Log from Underneath & Both Sides.
  • The Jaws Close to a Tight Minimum Opening.
  • The SG41HD has a Sturdy Mounting Plate. We Recommend the R45 Rotator, but the Grapple Can Also be Used with the R6 or R30 Rotators.
  • The Grapple is a Bypass Design, which Enables Controlled Release of the Load.
  • The Grapple has a Cylinder Piston that is 1.96" in Diameter.

Valby SG41HD Waste Grapple
The Jaws are Made of Hardox Steel & Have Wear Plates. The Picture Also Shows Plate on the Underside of the Grapple, that Protects the Cylinder from Damage.

Intermercato SG-52HD Stone Grapple
The Wear Plates on the Jaws are Approximately ¼" Thick.

Intermercato SG41HD Waste Grapples
Every Joint in a Valby Grapple has a Grease Fitting & a Bronze Bushing.

Valby SG 41 HD Rotator Grapples
The Stone Grapple has Heavy Pins, Thus They Have a Large Bearing Surface for Extended Life Expectancy. The SG41HD Hydraulic Grapple is Made Out of High Quality Hardox Steel.

Valby SG41HD Logging Grapples
The Grapple Comes with a Flat Mounting Plate with 4 Holes for 5/8" Bolts. If a Rotor is Needed, One Can Put One Onto the Mounting Plate.

Intermercato SG41HD Logging Grapples
Rotators that Fit the Bolt Pattern, the R30, R45, R45F & the R6, Rotators that Have 3, 4-1/2 & 6 Ton Lifting Capacities. The R45 is Recommended for Use with the SG41HD. The R45 is the Rotator of Choice for Several of Our Other Rotating Grapples. For More Information on the Rotators, Click Here.

Valby SG41HD Stone and Waste Rotator Grapples
The Grapple is a Bypass Design, which Enables Controlled Release of the Load.

Valby SG41HD Stone Grapples
The Grapple is a Bypass Design, which Enables Controlled Release of the Load.

Valby SG41HD Stone and Waste Grapples
The Grapple has a Cylinder Piston 5hat is 1.96" in Diameter.

Valby SG41HD Stone Grapples
The Width of the Grapple is 14". In a Closed Position It is 20" High.

Valby SG41HD Stone and Waste Grapple
The SG41HD has a Minimum Opening of 3-½".

Valby SG41HD Stone Grapple on Excavator

Valby SG41HD Grapple on Excavator

Valby SG41HD Stone & Waste Grapple

The Valby (Intermercato) Grapples can be Mounted Onto John Deere & Hitachi Compact Excavators by Means of a Quick Hitch. Above are Some Photos of a John Deere Excavator with a Valby SG41HD Stone Grapple. Other Versions of the Valby Grapples can Also be Hooked Up to the Quick Hitch.


SPECIFICATIONS
Max. Grapple Opening (A) 41.1"
Height Open (B) 21.5"
Height Closed (C) 20.2"
Min. Opening (D) 3.3"
Width of Jaw (E) 13.8"
Max. Lifting Capacity 3,307 lbs.
Working Pressure 2,900 PSI
Jaw Material Hardox 400
Weight 276 lbs.
Specifications & Designs Are Subject to Change Without Notice