H & S Model 430 Heavy Duty Manure Spreader

H & S Design and Engineering guarantees longer equipment life.

Struck level 275 cu. Ft., 430 Bu. unloading speed for the 430 Spreader - (2 speed chain drive) high speed: PTO speed 540 RPM. 8'8-1/2" per min. - Low Speed: PTO Speed 540 RPM. 4'8-1/2" per min.

Optional rear pan is available on the Model 430.

H & S spreaders have a massive unitized welded frame with heavy floor supports and side stakes, wrap around steel front corners. Strong rear main beater side panels are slanted for clearance and wider spread, and then welded to the strong 5" U channel side members. Compare with any on the market.

Front splash guards are standard equipment. The entire box inside, floor, sides of the rear hydraulic endgate use bonded polyethylene to marine type plywood to provide for easy cleaning and minimal freeze up. Condisderably less torque is needed to move a heavy load. The side flares are made of 10 gauge G210 culvert grade galvanized steel.

Model 430 can be equipped with the optional top beater to provide load leveling and spreading of high heaped loads. Notice how both beaters have no obstructions towards the sides and rear to provide for better spreading.

The 2-Speed apron drive is standard equipment. An optional variable speed hydraulic drive is also available.

A Semi-Liquid hydraulic endgate is standard equipment on the Model 430. A second hydraulic endgate cylinder is also standard.

The model 430 spreader has a 29" diameter beater with 14 replaceable paddles. The beater has two types of paddles, blunt for widespread and sharp ripper type for cutting and shredding. The beater side wiper blades are standard.

The strong oil bath bevel gear box that powers the beater is tapered timken roller bearing equipped. Also shown is the replaceable splined hub that welds into the main beater tube. The gear box utilizes a 4-jaw beater shutoff clutch and tractor sized spline shaft.

Gear box mechanisms and drive for the beater and apron are timken tapered roller bearing equipped. The beater drive gear box is 1-1 1/2 bevel gear oil bath equipped with a 4-jaw over running clutch for beater shutoff. The apron drive is a 50:1 bronze worm gear with shear bolt protection.

Adjustment for the main apron is easy, by simply loosening the two side bolts and drawing up the long bolt.

H & S uses cast special steel alloy apron idler slides instead of idler sprockets making for years of dependable service.


MODEL 430 SPECIFICATIONS
Top of Flare Width 68" (173 cm)
Inside Width 60" (152 cm)
Inside Length 16'6" (5.1 M)
Inside Depth 40-3/8" (102 cm)
Overall Width with Standard Tires 107" (272 cm)
Spindle Size 2-1/2" (6 cm)
Overall Length 23'2-1/2" (7.1 M)
Overall Loading Height - Top of Flare 63-1/2" (161 cm)
Overall Height with Hyd. Endgate 63-1/2" (161 cm)
Diameter of Beater 29" (74 cm)
Upper Beater Optional
Weight with Tires 5,220 lbs. (2,368 kg)
Capacity - Old Rating 430 Bu.
Capacity Cu. Ft. Struck Level 275
Rear Hydraulic Endgate Standard
Semi Liquid Rear Pan Optional
PTO Speed 540 - Standard
1000 - Optional
Jack Standard
Drive 2 Speed
Variable Speed Hyd. Drive Optional
Front Splash Panel Standard
Hyd. Cyl. on Hyd. Endgate 2
Main Apron Chain T-Rod
Standard Tire Size 16.1 x 16.5
SEE OPERATORS MANUAL FOR WARRANTY DETAILS AND LIMITATIONS. H&S RESERVES THE RIGHT TO CHANGE ITS PRODUCTS OR THE DESCRIPTION AT ANY TIME WITHOUT NOTICE OR OBLIGATION. MODELS AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.